EMT Practice Test

1. Question Content...

---

Question1: Refer to the exhibit.

What configuration is needed in order for "show LLDP configuration" to show this output?

Question2: Refer to the exhibit.

All four switches in the diagram have been configured with the region name "Aruba1".
What two other MSTP configurations must match for switches within the same MST region? (Choose two.)

Question3: Review the exhibit.
As the frame traverses from **PC-1** to **Server-1**, the VLAN tag will be removed.
Click on the interface (circled in green) where the VLAN tag will be removed.

Question4: Your customer has 349 users in a two-story building.
What are two benefits of a 2-Tier design? (Choose two.)

Question5: Which two port characteristics must match between LAG interfaces? (Choose two.)

Question6: What are two methods for remotely managing an Aruba AOS-CX switch? (Choose two.)

Question7: What are two mechanisms supported on AOS-CX 6300 switches used in Multi-active Detection to determine the status of the Primary member? (Choose two.)

Question8: You have completed a successful VSF stack between two switches.
Without manually assigning a backup switch, what is the expected output when issuing a show vsf command?

Question9: What are the benefits of a 3-Tier design over a 2-Tier? (Choose two.)

Question10: Match each network protocol to the correct server listening port. Not all answers will be used.

Question11: What are the commands to disable SSH and HTTPS services from the default VRF?

Question12: What connectivity commands are available on AOS-CX switches? (Choose two.)

Question13: Refer to the exhibit.

Using the static IP address configured above, what is the converted binary value of the third octet assigned to the local interface?

Question14: Match each description to the correct management tool for Aruba AOS-CX.

Question15: The following command is issued:
Switch# checkpoint rollback start
What is the result?

Question16: Which switch supports a maximum of 8 line-cards, 3 fabric modules, and 2 management cards?

Question17: Core(config)# user admin password
Core(config)# interface mgmt
Core(config-if-mgmt)# ip static 10.254.16.89/22
Core(config-if-mgmt)# default-gateway 10.254.19.129
Core(config)# ssh server vrf mgmt
Core(config)# https-server vrf mgmt
You are tasked with configuring the Core switch to be managed by NetEdit. Currently, the Core switch is at factory-default settings.
Which two steps are missing? (Choose two.)

Question18: Which field in the IPv4 header indicates whether the IP packet carries TCP or UDP traffic?

Question19: Interface 1/1/1 is up
Admin state is up
Link transitions: 1
Description: TO_PC-1
Hardware: Ethernet, MAC Address: 00:11:22:33:44:55
MTU 1500
Type 1GbT
Full-duplex
qos trust none
Speed 1000 Mb/s
Auto-negotiation is on
Flow-control: off
Error-control: off
MDI mode: MDIX
VLAN Mode: access
Access VLAN: 1111
Which command will produce the above output?

Question20: Refer to the exhibit.

Switch-1 is not the root bridge. The ports shown are all the connected pointtopoint interfaces. What Role (hidden by the blue rectangle) will be assigned to the Lag 1 interface?

Question21: What is the login and password combination is used when first configuring an Aruba OS-CX switch from factory defaults?

Question22: Which two options are the Layer 2 protocols? (Choose two.)

Question23: Refer to the exhibit.

What change on Core-1 will result in a successful ping to 10.1.1.254 from the management interface?

Question24: Refer to the exhibit.

All switches are running Aruba OS-CX. While working in the terminal of Access-2, you are unable to reach Server-1 using SSH.
What is the correct command to ping Server-1 from Access-2 to test reachability?

Question25: Match the available stacking feature to the correct AOS-CX switch model. Stacking features may be used more than once.

Question26: Refer to the exhibit.

The command show LLDP neighbor-info gets typed into Access-1. All switches are Aruba OS-CX switches. What is the output of this command?

Question27: Which network category applies to a SOHO internal network?

Question28: Refer to the exhibit.


What command will display the debug l2mac events?

Question29: Which two commands will save the running-config so that changes will be loaded automatically on the next reboot? (Choose two.)

Question30: What is Deep Packet Inspection?

Question31: Which statement is correct regarding powering an Aruba Access Point?